Floor Stripping and Waxing
Floor Stripping and Waxing in Roseville
Remove worn finish and apply a fresh coating to commercial flooring. Each resilient and VCT floor is assessed first, so the treatment suits the surface.
A fresh finish for worn floors
Stripping removes an existing floor finish before a new finish is applied. We strip and refinish VCT and other resilient tile floors.
When a different method is a better fit
A dirty or worn-looking floor does not always need complete finish removal. Scrubbing, recoating, polishing or burnishing can be the better fit for a floor that is dull but intact. Explore commercial floor care options.
Preparing the work area
We note what moves and which rooms stay open, then book a window long enough for the finish to cure.
Allowing the finish to dry or cure
The selected finish and project conditions set the return-to-use time. The treated area stays closed until the finish has dried or cured.
Timing a strip-and-wax project
Stripping and waxing takes a floor out of use for a while, so the work window is chosen with care. Weekends, evenings, and slow periods leave the new finish undisturbed while it dries or cures, and the project area is marked out in advance.
Between full projects, recoating or burnishing can keep a busy VCT floor looking fresh longer. This works well for breakrooms, corridors, and retail floors in Citrus Heights or Lincoln, while routine mopping through janitorial service carries the finish between projects.
How a strip-and-wax project runs
The day begins with the work area cleared and marked off, so nobody wanders onto a wet floor. A stripping solution loosens the old finish, the floor is scrubbed to lift it, and the residue is picked up and rinsed away. The tile has to be clean and fully dry before any new finish goes down.
Fresh finish is then laid on in thin, even coats, each one drying before the next. The area stays closed until the finish can take foot traffic, and furniture returns only after that point.
Signs a floor needs full stripping
Burnishing that no longer brings the shine back, traffic lanes worn to bare tile, a yellowed cast and scuffs that will not lift all point to a full strip.
Our guide to when floors need stripping or a deep clean shows how to tell a full strip from a scrub and recoat.
Strip-and-wax for Roseville area properties
VCT and resilient tile show up across the local property mix: corridors in medical offices, breakrooms in corporate offices, and sales floors in retail centers. Each one has a different quiet window, from a closed weekend to the hours after the last patient leaves.
Medical suites follow the facility’s rules for timing and access, as our medical office cleaning page explains. Projects in nearby cities follow the same timing, and the Rocklin page covers how after-closing work fits busy storefronts.
Strip and wax costs for Roseville-area floors
Strip-and-wax projects carry a minimum charge, which matters most for small floors. Above that minimum, 2026 published pricing puts Roseville-area work at $0.45 to $1.00 a square foot. Open, well-kept VCT starts around $0.35, and small rooms, heavy buildup or many fixtures take the rate as high as $3.00.
Two projects show the spread. A 900-square-foot clinic corridor with doorways every few feet, stripped and refinished at $0.95, comes to $855. A 6,000-square-foot open retail floor at $0.48 runs $2,880, a lower rate because the machines cover long, open runs without stopping.
Signs that a floor needs full stripping, such as yellowed layers or finish worn through to the tile, also predict more passes and a higher rate. Base coats and finish coats each need drying time, so work squeezed into a single overnight window costs more than a project that can spread across a closed weekend. Furniture moves and tight layouts add time. If a scrub and recoat would serve the floor better, the assessment at the on-site walkthrough says so, and the quote follows that method. Strip-and-wax rates sit beside janitorial, porter and carpet pricing in our Roseville cleaning cost guide.
A few useful answers
Questions about commercial floor stripping and waxing
What should I share when requesting a quote?
Include the floor material if known, approximate area, visible wear, and existing finish. Note any spaces that must remain open during the work.
Is this the same as routine mopping?
No. Mopping removes routine soil. Stripping and waxing removes the old floor finish and lays down a new one.
How often should a commercial floor be stripped and waxed in Roseville?
A full strip and wax once or twice a year suits most commercial floors, with a scrub and recoat or burnishing in between. Busy entries, breakrooms and food areas wear through sooner, and a quiet office floor can go longer.
Can a strip-and-wax project be split into sections?
Yes. The project can treat one area at a time while other rooms stay open for business.
Can you wax a floor without stripping it first?
Yes, if the existing finish is clean and intact. A recoat adds new finish on top, while stripping is for finish that is worn through or built up with trapped soil.
How is furniture handled before a strip-and-wax project?
We list what needs to move at the walkthrough and plan the rooms around it, and nothing goes back on the floor until the finish is ready.
How are carpet and stone handled in a building that also has VCT?
Each surface gets its own method. Carpet receives spot treatment or extraction, and natural stone is cleaned with a product matched to its type and finish.
Services
Related services
Industries
Related industries
Resources